Search found 7 matches
- Tue Apr 17, 2007 10:50 pm
- Forum: General How-To & Discussion
- Topic: Australian Spudgun Laws.
- Replies: 221
- Views: 43389
This is the official South Australian Police email reply that i recieved this morning: I have your enquiry for response…. Spud guns are “prescribed firearms” by virtue of Regulation 8, being home made firearms. There are heavy penalties in the Firearms Act for possession of a prescribed firearm. The...
- Tue Apr 17, 2007 4:31 pm
- Forum: Ammo & Parts
- Topic: Laminating Small diameter inside larger diamater PVC
- Replies: 6
- Views: 1593
6000 N/m/m means that if you got a 1 meter long section of pipe, and clamped one end in a vice, the other end would deflect 1 meter if you if you put 600 kg on it. Now, I expect a 1 meter section would actually snap before it deflected one meter, so let's just say that it'd "take 60 kilograms to ma...
- Tue Apr 17, 2007 5:52 am
- Forum: Ammo & Parts
- Topic: Laminating Small diameter inside larger diamater PVC
- Replies: 6
- Views: 1593
Seems i'm stuffed anyway, just went out and checked what i was going to use for the chamber. It's DN100 SN6 as layed out in AS/NZS 1260 (Australian / New Zealand standards). I.e. not pressure pipe, but according to this document http://www.vinidex.com.au/vinidex/live/RESOURCES/IMAGES/technotes/TN-14...
- Tue Apr 17, 2007 4:57 am
- Forum: Ammo & Parts
- Topic: Laminating Small diameter inside larger diamater PVC
- Replies: 6
- Views: 1593
y not just save some time and sleeve some pn18 pipe in another piece then wrap it in fiberglass it would be able to hold allot more pressure Because what I specified in my original post is the best that I can get at this time :( . The results that were calculated using the spudtech spreadsheet were...
- Tue Apr 17, 2007 4:38 am
- Forum: Ammo & Parts
- Topic: Laminating Small diameter inside larger diamater PVC
- Replies: 6
- Views: 1593
Laminating Small diameter inside larger diamater PVC
For the reservoir chamber on the gun I intend to build IF the S.A. gun laws allow it, i was thinking of laminating some 90 PSI PVC inside some of the same rating (i can get two diameters that will fit each other like a glove) and then wrapping the whole lot with several layers of fibreglass reinforc...
- Tue Apr 17, 2007 3:57 am
- Forum: Pneumatic Cannons
- Topic: Pope/Gardenmate sprinkler valve mod as detailed in..........
- Replies: 0
- Views: 1858
Pope/Gardenmate sprinkler valve mod as detailed in..........
this thread: http://www.spudfiles.com/spudtech_archive/viewtopic.php?t=12043&postdays=0&postorder=asc&highlight=sprinkler+valve+mod&start=20 I have two of these. Now i intend to use this method on them. Forgive my ignorance, but if the diagonal hole is widened (speaking of the diagonal hole show in ...
- Tue Apr 17, 2007 2:27 am
- Forum: General How-To & Discussion
- Topic: Australian Spudgun Laws.
- Replies: 221
- Views: 43389
Prescribed Firearms legislation: http://www.legislation.sa.gov.au/LZ/C/R/FIREARMS%20REGULATIONS%201993.aspx OK, thats the current south australian firearms legislation. I've emailed to confirm, but as far as i can tell, any sort of home-made firearm is a prescribed firearm. This is a good and a bad ...