Just a quick question

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
Post Reply
User avatar
Wombat
Private 2
Private 2
Posts: 29
Joined: Sat Oct 13, 2007 9:26 pm

Mon May 26, 2008 12:46 pm

From your experience, how much pressure can Plumbers-Goop ("Amazing Goop") hold? I used it to seal a tank on my pneumatic, and I don't want to put too much pressure in it.
Top
User avatar
jrrdw
Moderator
Moderator
United States of America
Posts: 6572
Joined: Wed Nov 16, 2005 5:11 pm
Location: Maryland
Has thanked: 39 times
Been thanked: 22 times
Contact:
Contact jrrdw

Donating Members

Mon May 26, 2008 12:55 pm

Thats a good question, since you have some figure out a safe way to test it and inlighten the rest of us..... :wink:
Top
User avatar
no-limit
Private 4
Private 4
Posts: 92
Joined: Thu Apr 10, 2008 11:15 pm
Contact:
Contact no-limit

Mon May 26, 2008 10:11 pm

Yeah, then we'll all know.
Top
User avatar
DYI
First Sergeant 5
First Sergeant 5
Antigua & Barbuda
Posts: 2862
Joined: Sat Jul 07, 2007 8:18 pm
Location: Here and there

Tue May 27, 2008 4:05 pm

How big is the hole you're trying to seal? Your question is like asking how much pressure steel can hold...
Spudfiles' resident expert on all things that sail through the air at improbable speeds, trailing an incandescent wake of ionized air, dissociated polymers and metal oxides.
Top
keep_it_real
Specialist 3
Specialist 3
Posts: 320
Joined: Sat Dec 23, 2006 4:41 pm
Location: Bend, Oregon

Tue May 27, 2008 4:31 pm

I used it a couple times to seal a threaded brass fitting in an unthreaded hole (it probably got partially threaded just from putting it in there but). It holds at least 100 psi. Also used it to seal modded sprinkler valves where the solenoid goes. Seems fine but I'll epoxy more. If your talking about sealing on an end cap or something than that's beyond me.

I'm a big fan of putting myself and a pump on one side of a door and the potentially explosive test subject on the other side then shaking it around.
Top
User avatar
Wombat
Private 2
Private 2
Posts: 29
Joined: Sat Oct 13, 2007 9:26 pm

Tue May 27, 2008 4:49 pm

Alright, here's the deal. I haven't yet gotten a chance to test out how much pressure it can hold, but I'll try to soon.

The set up is like this- A fire extinguisher tank, with a 1/2 brass ball valve glued inside of the top. There is also set screw (that I made out of a 5/16" bolt) that is wrapped in teflon tape holding the two pieces together. Before I shoved the ball valve into the extinguisher, I wrapped the bottom of it with lots of teflon tape. then, I coated the inside of the neck of the extinguisher in goop. after I shoved the ball valve in, I put the set screw in, and coated all of the connection with goop.

Edit:

Here is a picture - Image
Last edited by Wombat on Tue May 27, 2008 8:55 pm, edited 1 time in total.
Top
TurboSuper
Corporal 5
Corporal 5
Posts: 986
Joined: Thu Jun 16, 2005 1:44 pm
Been thanked: 1 time

Tue May 27, 2008 7:51 pm

I actually happen to know this from experience.

Plumbers Goop will start to fail at around ~50 PSI of constant pressure. It begins to bubble, and will then rupture.

They've changed the formula of it- it used to be unstoppable, now it's pretty suck. Best to just roll with JB Weld.
"If at first you dont succeed, then skydiving is not for you" - Darwin Awards
Top
User avatar
Wombat
Private 2
Private 2
Posts: 29
Joined: Sat Oct 13, 2007 9:26 pm

Tue May 27, 2008 8:57 pm

Alright, I'll try putting about 75 psi into it, and if it begins to fail, I just might have to peel it all off, and re glue it with something stronger.
Top
Post Reply

Return to “Pneumatic Cannons”