Similar to that, and i need to cut part of it of for a custom part, I have tried a Hacksaw but it will take forever to cut it, any ideas?Help Cutting Steel!
-
Goats spudz
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
Ok, i have some stainless steel hydraulic fittings. Similar to that, and i need to cut part of it of for a custom part, I have tried a Hacksaw but it will take forever to cut it, any ideas?
Similar to that, and i need to cut part of it of for a custom part, I have tried a Hacksaw but it will take forever to cut it, any ideas?-
mattyzip77
- Sergeant 3
- Posts: 1249
- Joined: Tue Jun 28, 2011 12:22 pm
- Location: Taxachusetts
Try using a cut wheel on a hand grinder!!Or a sawzall,!!!!!!!!!
Go Bruins!!!!
-
Goats spudz
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
I Dont own a sawzall and an angle grinder isnt precise enough
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
A good 12 inch hacksaw with a bi-metal blade should make short work of it.
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
mattyzip77
- Sergeant 3
- Posts: 1249
- Joined: Tue Jun 28, 2011 12:22 pm
- Location: Taxachusetts
How is it not accurate enough??? As long as you clamp it down good you wont have a problem. Just take your time!!!Goats spudz wrote:I Dont own a sawzall and an angle grinder isnt precise enough
Go Bruins!!!!
-
Goats spudz
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
also i have lost the thing that holds the guard onmattyzip77 wrote:How is it not accurate enough??? As long as you clamp it down good you wont have a problem. Just take your time!!!Goats spudz wrote:I Dont own a sawzall and an angle grinder isnt precise enough
What are you planning to do here? Maybe we can give you a work-around so you don't even have to cut the fitting....
-
Goats spudz
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
i have cut it, my blade was dull so i bought some new high speed blades for my hacksaw. its a custom part for my air tank.
What do you need a guard for? wear googles/glasses and cut away.Goats spudz wrote:also i have lost the thing that holds the guard onmattyzip77 wrote:How is it not accurate enough??? As long as you clamp it down good you wont have a problem. Just take your time!!!Goats spudz wrote:I Dont own a sawzall and an angle grinder isnt precise enough
Goats spudz wrote:i have cut it, my blade was dull so i bought some new high speed blades for my hacksaw. its a custom part for my air tank.
high speed blades for a hacksaw? how fast can your hand cut through metal?
90 pulls a minute?
-
Goats spudz
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
its the thing that stops you cutting your fingers offsco77 wrote:What do you need a guard for? wear googles/glasses and cut away.Goats spudz wrote:also i have lost the thing that holds the guard onmattyzip77 wrote: How is it not accurate enough??? As long as you clamp it down good you wont have a problem. Just take your time!!!
-
Crna Legija
- First Sergeant 2
- Posts: 2333
- Joined: Sun Jul 20, 2008 5:14 am
- Location: australia
iv had hacksaw blades get hot enough to discolourjsefcik wrote:high speed blades for a hacksaw? how fast can your hand cut through metal?
90 pulls a minute?
more importantly its what stops a broken disk from implanting itself into your headGoats spudz wrote:its the thing that stops you cutting your fingers off
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
-
Gaderelguitarist
- Corporal
- Posts: 580
- Joined: Sat Aug 16, 2008 9:56 pm
- Location: Columbia, MD
- Contact:
Hacksaws and a set of files are all I use for cutting metals. Use the right blade like JSR suggested, and you'll be through it in no time.
Only if you're a slow wimp90 pulls a minute?
so many muchness