Which Breech Loader?

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
User avatar
Hydra
Specialist
Specialist
Posts: 131
Joined: Sat Mar 08, 2008 11:58 pm
Location: New South Wales, Australia

Sat Oct 18, 2008 3:32 am

Okay, I have made a SValved Pneumatic rifle. Im thinking about creating a Breech loader for the gun.
Im not sure if i should use a breech loader that moves the barrel, or a breech loader that moves a piece of pipe around the barrel.
What are the pros and cons for each?
User avatar
psycix
Sergeant Major 4
Sergeant Major 4
Posts: 3684
Joined: Mon Jun 25, 2007 7:12 am
Location: The Netherlands

Donating Members

Sat Oct 18, 2008 4:58 am

When your barrel is long-ish or just really heavy it becomes difficult to shove the whole barrel up and down.
The whole part of bolt-action breech loaders is to find a piece of pipe that fits around your barrel. One option is to use an coupler for that, but since a coupler is somewhat short, it becomes hard to move the whole barrel. (not enough support n stuff)

Also it is safer to physically attach the barrel to the gun by threads or glueing since your bolt-action locking MAY fail if it isnt built strong enough, and your barrel will go flying.

I'd say use a piece of pipe that moves around the barrel.
Till the day I'm dieing, I'll keep them spuddies flying, 'cause I can!

Spudfiles steam group, join!
User avatar
FishBoy
Corporal
Corporal
Posts: 575
Joined: Tue May 27, 2008 5:51 am

Sat Oct 18, 2008 11:37 am

if you have a small diameter barrel (.5" to 1") then you can just cut a hole in the top to load the projectile, and then grind out a coupler so it slides over. I have done this, and it works very well.
"You polish a turd, it's still a turd"

Remember DYI!!!
User avatar
STHORNE
Sergeant 3
Sergeant 3
Posts: 1208
Joined: Wed Feb 14, 2007 7:50 pm
Location: Kewaunee, Wisconsin

Donating Members

Sat Oct 18, 2008 1:27 pm

The second option would probably be best if you wanted to keep your barrel stable
Forum Rules - follow them or else!
“Happiness is the meaning and the purpose of life, the whole aim and end of human existence”
nivekatoz
Specialist 2
Specialist 2
Posts: 237
Joined: Sat Nov 25, 2006 7:05 pm

Sat Oct 18, 2008 3:28 pm

I think about that stuff all the time. Its starting to drive me nuts.. :dontknow: I give up ..Im just going to make my cannon a muzzle loader, and be done with it already. Now Im starting to find a way to mount a sight. :idea:
User avatar
Hydra
Specialist
Specialist
Posts: 131
Joined: Sat Mar 08, 2008 11:58 pm
Location: New South Wales, Australia

Sat Oct 18, 2008 5:03 pm

Fishboy my barrel is 1/2 inch, so I will probably use the sliding coupling idea.
But wont this leak?
User avatar
spudy buddy
Specialist
Specialist
Posts: 123
Joined: Thu Nov 29, 2007 9:27 pm

Sat Oct 18, 2008 10:37 pm

yeah you should probably put some o-rings on it for a good seal, but it'll only leak for a very short period of time since all the gas is out the barrel in probably less than a second( depending on your c:b ratio it might be a bit more). for optomal performance i would put o-rings on it but they're not needed all that much.
Spudy Buddy
User avatar
psycix
Sergeant Major 4
Sergeant Major 4
Posts: 3684
Joined: Mon Jun 25, 2007 7:12 am
Location: The Netherlands

Donating Members

Sun Oct 19, 2008 10:13 am

Yes, it will leak, but not significant unless the coupler is very very loose or your barrel is really long and projectile really heavy.
You could always add duct tape as ghetto solution, and to do it the good way: O-rings
Till the day I'm dieing, I'll keep them spuddies flying, 'cause I can!

Spudfiles steam group, join!
User avatar
Hydra
Specialist
Specialist
Posts: 131
Joined: Sat Mar 08, 2008 11:58 pm
Location: New South Wales, Australia

Mon Oct 20, 2008 2:35 am

Alright, Ill use O-Rings.
Post Reply