SpudFiles

Well spudfiles, I've been quite busy with this project for the past few weeks.

SPECS:

Valve: 1/4'' QEV from ebay piloted by a 1/4'' slide valve also from ebay.
Chamber: 1/4''x6'' steel pipe nipple
Barrel: 30'' Brass tight bore Airsoft barrel cased in 1/2 PVC
Operating pressure: 25-450psi (so far)
Air source: remote (backpack ) Paintball HPA tank and regulator.
Magazine: 12 round, spring loaded, non-removable magazine.
(the magazine is non removable, and is loaded by sliding the follower all the way down, where it locks, and then loading through a port in the side of the mag.)
Scope: I bought the scope today at meijer, 8 dollars for a 14x zoom cross haired Tasco scope....

This gun is true semi-auto, and fires with each pull of the trigger.
I cannot pull the trigger faster than it will shoot.

The stock was made from a 2x6, and took aprox... 4 hours.

Photos:






This gun will happily punch through the bottom of a pop can at as low as 50 psi. At 450 psi a 20g king Armour BB chips my sidewalk.

I hope to take a damage video soon.
EDIT:
Video[youtube][/youtube]
link
http://www.youtube.com/watch?v=2aHkqTRIeRU
Video was taken at 250psi. (not Airsoft war safe.)
This different sounds in the video are caused by a few doubble feeds.

My detent seems to be a little lose. hahah.... also about halfway through shooting... i ran out of ammo(12 rounds), and after that was loading them 1 at a time into the clip.

nice... is there a trigger of do you have to manually operate the slide valve ?

For now i use the slide valve.

The trigger is a W.I.P

Also, i do have another barrel/breech assembly for it... made of copper.... just the right size for AA Batteries 8)

Damage photo... semi auto fire... 2 clips at a pop can from about 25 feet.
300 psi

Awesome, thats all I can say, clean, powerful, somewhat compact, Im sure Im not the only one whos going to ask this, any chance of a video.

Sweet, I just designed an airsoft semi auto kinda like that.

clemsonguy1125 wrote: Im sure Im not the only one whos going to ask this, any chance of a video.

As soon as i can take one. Yes. For sure.

I have a few different muzzle breaks... that drastically change the sound... i will be sure to get those in the video as well.

For now... more pop carnage.



Just a clip load in a pop can from about 25 feet at 100 psi this time.

(Darn macro button....)

Awesome, cant wait, by chance is this the QEV you used

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

Yes, that QEV, Only, i bought a lot of 7.... for $40usd.

I pushed one to its limits...... well... i tried to... but i refused to fail even at 700 psi... and i did not want to go any higher.

EDIT

video is now in the first post.

Wow looks really good!!! Lemme guess, does it shoot half a mile?

Wow looks really good!!! Lemme guess, does it shoot half a mile?

Actually it might get close with other ammo...

haha.

Yes, i used to be a noob. I have learned alot though, and now realize the limitations of my cannons.

This particular cannon would never even shoot close to that kind of range.... simply because of the tiny, light projectile, and the low amount of energy involved.

Any ways, back on topic... what do you think of the stock? i am particularity proud of that stock... hard to tell in the photos... but it is very rounded.... and looks pretty darn good if i say so myself.

jhalek
Nice looking piece. You should be damn proud of your creation and accomplishment.

Any ways, back on topic... what do you think of the stock? i am particularity proud of that stock... hard to tell in the photos... but it is very rounded.... and looks pretty darn good if i say so myself.

Yeah, I forgot to say... The stock looks REALLY cool. It's very original and almost futuristic looking (being so curvy I guess)... Great job 8)

Nicely done! And using off-the-shelf parts, well made

One small thing, does it have an integral suppressor or did you just reinforce the barrel? Sounds pretty loud in the video.