SpudFiles

I finished my first cannon, and it looks kind of ghetto. I wanted to see if you guys had any suggestions for improvements.

Currently:
Inline spray and pray launcher
3''x14'' to 1.5''x60'' (C:B .85:1)
3'' computer fan
BBQ Sparker
Chamber-Short for two gaps

Going to add:
Going to redo the wiring - aesthetics
Camlocks
Ball-Valve for easy venting
Propane...via Schrader valve
Propane Meter that is a side component.

I had a hard time getting the wires to stay put in the inserts..so I epoxied them in place. Another limitation I had was with the size of the sparker. It's hard to make something that big look nice.

Attached are the pictures. Thanks for the suggestions.

holy crap that is a big sparker ! could you maybe take the components out & install then into a smaller box? i use the same exact metering setup that you do .i just drilled , tapped another female quick connect into my chamber but with a 90 degree elbow so it lays flat against the chamber ,, also a paint job goes a long was for looks

Lol. The size of the sparker was my biggest problem..but it runs off of one aa battery, and can throw down some good sparks.

I thinking that I will do away with the box, and hide everything in a handle I make...it will cover all of the wires. Then, when I paint it..it will look awesome.

If you're gonna make a handle, make it so everything can fit in there, and hide all the electrodes under the tee/saddle. Also instead of strapping it on, just use 2 nice wood screws.

If you decide to use a box, get a smaller one from Radio Shack and mount it with 2 machine screws in the bottom of the box through the chamber wall. Giant hose clamps - or any for that matter - are ugly. Here's the fun part: Send your fan power through those 2 screws to eliminate visible wires. I suppose you could actually do that with the spark leads too.

Be sure to use crimp-on connectors to keep the leads in good contact with the screws.

Plug the old lead holes with small screws. Make on of them into your propane injection port. Hide one or 2 more by mounting the box so it hangs over it.

Paint it.

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

People seem to live by that double layer rule, but throughout my adventures, I've found that a well-drilled and tapped hole through a single layer is nothing at all to worry about. When practical, I will mount anything I can through a double layer, but when ergonomics or even aesthetics come into play and suggest for a different positioning, I find that those parts mounted through a single layer can be more than secure enough for everyday use if done right.

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

Of course it's possible with some designs, and it's good practice.

I've seen failures, but actually none because of single-layer drilling. I've actually had chambers crack in cold weather - nowhere near the holes! Luck maybe?

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

If you're gonna make a handle, make it so everything can fit in there, and hide all the electrodes under the tee/saddle. Also instead of strapping it on, just use 2 nice wood screws.

That is the idea.

If you decide to use a box, get a smaller one from Radio Shack and mount it with 2 machine screws in the bottom of the box through the chamber wall. Giant hose clamps - or any for that matter - are ugly. Here's the fun part: Send your fan power through those 2 screws to eliminate visible wires. I suppose you could actually do that with the spark leads too.

Can't do that. The box I'm using is the smallest I could find that would work. Besides, I am going to put everything in a handle.

Be sure to use crimp-on connectors to keep the leads in good contact with the screws.

That is what I am using.

Plug the old lead holes with small screws. Make on of them into your propane injection port. Hide one or 2 more by mounting the box so it hangs over it.

Took me a second to understand what you were saying. But, no. I am going to put my propane injection by my fan, through two layers. I am thinking of doing away with the box..it's really ugly.

Paint it.

Yes. Maybe an olive green, with black lettering.

The only thing that is not tapped through double layer is my spark electrodes. I didn't put them through double layer because I have them set on even spacing through the chamber. We seem kind of split on the double layer thing. I understand that you can never be too safe. As a first edition, if it fails, no biggy. I'll learn my lesson, and take what I can.

That is a nice cannon SpudBlaster15