Deathray MP now running on unregged 12 gram!!

[MrCrowley]

Such as, Exhibit A

I would post that again in a reply to your post, but I think one headbanging animation is enough for one page


@BtB

Yeah, you're right the silencer just looks too good to remove it

[jackssmirkingrevenge]

I think one headbanging animation is enough for one page

Or is it?

[Brian the brain]

Enough with the facepalmheaddeskfrontteethdonatingtothekeyboard thing.

Go hijack your own thread buddy!!

[jackssmirkingrevenge]

*attempts to run away but is instantly cut down in a rapid burst of hypersonic airsoft BBs*

[POLAND_SPUD]

BtB make sure that this does not happen to you -->


I hope you don't shoot it indoors ?

[Brian the brain]

@Jack: You get intimidated by my face already....BOOH!

I did shoot it indoors.

As I said, a ricochet at half the pressure hurts like hell through a thick sweater.

Some damage and inner workings:

[Brian the brain]

edited the above

[THUNDERLORD]

Your gun is my favorite one on here. i wish there was a favorites key on spudfiles like youtube has.

[POLAND_SPUD]

I like that descrition with a sl#t (pic with a can)

yeah lead BBs are the way to go. cheap plastic BBs are ussually 0.2 g each lead BBs are about 1g ? so I assume you could get about 3 times (?) the power you have now... well I am just guessing

[Brian the brain]

We could all add a poll to our cannons asking just one question:
Is this your favorite cannon? And then compare count.

There is no doubt lead bb's give better results.My fist experimental vortex block strafer ripped up steel cans at 20 bar with a smaller tank.
This one could do 3 x that.

I 'm hesitating getting 5.5mm bb's ( .20)
I believe the round ones are hard to get, as opposed to pellets.
They wouldn't jam, since the have 0.5 mm clearance.

[POLAND_SPUD]

5.5mm BBs seem to be something rather rare.... and obviously a 0.5mm gap would affect performance... does it jam often ?

AFAIK 1/2" marbles are cheap
lol a 12.7 mm BBMG.... that would be something better than... well..... better than anything

[Brian the brain]

I have .50 roundballs for muzzle loading blackpowder rifles.About a 100 of em.
And the fit reasonably well into 15 mm pipe.
'Not too sure the valve has enough flow...
and I don;t already want to damage the paint..It was the last I had..

[POLAND_SPUD]

I understand that you are using your pressure washer handle as a valve right ? I suppose its flow isn't as good as it could be but defienately you're going to get more range with 0.5" lead balls than with plastic BBs

that 47mm cannon looks massive.. how much does it weight ? about 12 - 15 kg ? I suspect that the weight absorbs the recoil to some extend but still it has to kick like a mule... that barrel could be a bit longer to get more power but it would add a kilo or two to the overal mass.... also does that blowgun seal well at 30 bar ?

[MrCrowley]

Does that can mean 'flat black' in English? - If it's even a spraypaint can and not silicon spray or somethign like that...

Cool dmaage pics, you definitely owned that can.

I just wish you had unlimited lead BB's

[Brian the brain]

that 47mm cannon looks massive.. how much does it weight ? about 12 - 15 kg ? I suspect that the weight absorbs the recoil to some extend but still it has to kick like a mule... that barrel could be a bit longer to get more power but it would add a kilo or two to the overal mass.... also does that blowgun seal well at 30 bar ?

This is the short breakbarrel. ( it swings up to breechload)I have another one about 70 cm long, but the power was so ridiculous, I could sacrifice some and go for the look I wanted.
Check out: http://www.spudfiles.com/forums/overkil ... nd-camo-t8 855.html
The same cannon, just with the large barrel.
Blowgun manages 26 Bar so far.Haven't felt like trying 30 in my back yard.
It leaks while filling when half open.

Does that can mean 'flat black' in English? - If it's even a spraypaint can and not silicon spray or somethign like that...

Yep, that's flat black spraypaint allrighty..Don't leave home without it

Now for the serious bit: