Page 1 of 1
i need help with my bbmg
Posted: Tue Jun 19, 2007 1:46 pm
by the enforcer
hi can sombady help me with my bbmg
all my balz are just going around in the chamber
here is a vid he is very domb bud i want to know if i can spent my money on it
so i need to know do i need a blok thing ?
this is how he looks right now
http://youtube.com/watch?v=C75BlF7_cLA
Posted: Tue Jun 19, 2007 2:16 pm
by Brooner115
HAHAHAHAHAHAHAHAHAHAHAHAHAHAHA
dude Im really sorry but ah u really threw me off with your spelling and decisive configuring but umm it depends on what kind of gun you wanted to make a Cloud or a Vortex and uummmm... WIKI!!!!
Posted: Tue Jun 19, 2007 2:42 pm
by the enforcer
lol i am not so good at english bud what is the difirense intuse a vortex and a cloud ?
what is the diffitens ??
Posted: Tue Jun 19, 2007 3:37 pm
by keep_it_real
Are you just blowing into it? If you are, a vortex block like the one in the picture would be good to build. If not, I bet a lot of air is leaking out the "end caps" instead of all through the barrel. Although it's hard to tell, the barrel looks to big for airsoft bbs.
Posted: Tue Jun 19, 2007 3:40 pm
by the enforcer
well i have a compressor so i dont want to blow
i want with the thing on the picture
sow can sombady show me a photo how to mount it in the gun ?
greetz paul
Posted: Tue Jun 19, 2007 3:55 pm
by Redcoat
Aha.I don't think you're wooden endcap is all that airtight.
Posted: Tue Jun 19, 2007 4:18 pm
by spudthug
it doesnt have tobe airtight..u cant make a cloud with the hole in the back it has to be at the bottom..
why not take 2 dollars to a hardware store and get some pvc dude...
Posted: Tue Jun 19, 2007 4:30 pm
by singularity
Is that hot glued together?
i think you should scrap that thing and start over, the pieces for a new one are going to cost $10. heres what you need to get...
PVC primer and glue
1 1/2 cap
1 1/2 clean out
six inches of 1 1/2 PVC
a 1/4 ball valve or blowgun (either will work)
and a barrel
search this site for "cloud bbmgs" to figure out how it all goes together
the block you are referring to is know as a vortex block, they require some basic machining skill and are not necessary. but they do allow for more consistant firing
in order for the gun your making to work you need to make the hole gun airtight except for the barrel, the principal is pressurized air is introduced into a chamber filled with bbs and the bbs are literraly sucked out of the barrel.
ps- are you using some sort of translator or is your english just bad?
Posted: Tue Jun 19, 2007 4:33 pm
by spudthug
six inches of 1 1/2 PVC
too much...around 3 inches for best performance...
1 1/2 clean out
cleanout, cleanout cap, coupler all 1 1/2....
in order for the gun your making to work you need to make the hole gun airtight except for the barrel
it doesnt need to be airtight...althoguh it helps.. as it isnt storing any air it is jsut going out the barrel
also the hole for the blowgun needs to be at the bottom of the gun for a cloud...
Posted: Tue Jun 19, 2007 7:31 pm
by Mac/pistol man
W, T, F..... Is that..... Packaging tape? Wood? hot glue????
Posted: Wed Jun 20, 2007 2:16 am
by Redcoat
wait i thnk your barrel is of too higher calibre?
ANd spudthug th hole doesnt have to be in the botom my cloud bbmg doesnt have it in the bottom it has t in the back like th enforcer's.
Posted: Wed Jun 20, 2007 4:50 am
by the enforcer
oke i go make one now and that one will be nicer 8)
so lets see i have a lots of crap like this here
:
should i use that blow gun ?
Posted: Wed Jun 20, 2007 5:21 am
by Redcoat
well maybe but i think that duster will decrease performance.Unless you can cut it off somehow.
Posted: Wed Jun 20, 2007 6:45 am
by the enforcer
sure i can cut it off just tell me ware i need to cut it
and i cut it
Posted: Thu Jun 21, 2007 6:41 am
by the enforcer
but should i do it with this blow gun or another one ?