Page 1 of 2
Help QEV Sprinkler valve trouble
Posted: Mon Jul 22, 2013 5:01 am
by Maasoon
Hey everyone i have recently started to build my first pneumatic spud gun as i have only ever built propane ones before. I purchased a solenoid sprinkler valve and have epoxied the solenoid cavity and attached a blow gun with a brass nipple as a guide on you tube suggested. The problem i have is that air still flows out of the barrel not quickly but at a noticeable pace also the blow gun does not increase the air flow when triggered. i was reading so threads about how a bigger equalizing hole would help but i don't think mine even has one. what should i do should i poke a pin through the diaphragm? to crate one?
Thanks Mason
Posted: Mon Jul 22, 2013 5:17 am
by jackssmirkingrevenge
Photos of your setup?
dont have any atm
Posted: Mon Jul 22, 2013 5:22 am
by Maasoon
its just a 1" sprinkler valve with a normal blow gun screwed in
Posted: Mon Jul 22, 2013 5:52 am
by jackssmirkingrevenge
what model sprinkler valve?
can you take pictures of how and where you installed the brass nipple?
It's hard to give advice without looking at the thing.
Posted: Mon Jul 22, 2013 6:42 am
by Maasoon
I don't know how to upload photos but I can email them[/img]
Posted: Mon Jul 22, 2013 6:47 am
by Maasoon
Emailed them to you to the address on our profile
Posted: Mon Jul 22, 2013 8:00 am
by jackssmirkingrevenge
You seem to have done everything right, my feeling is that you are not filling the chamber fast enough. Are you sure there was no dirt on the diaphragm when you put it back together?
Posted: Mon Jul 22, 2013 9:38 am
by dewey-1
Also need pictures of spring location and diaphragm which may help.
What brand and model is the sprinkler valve?
Posted: Mon Jul 22, 2013 1:11 pm
by jackssmirkingrevenge
here you go
Posted: Mon Jul 22, 2013 4:07 pm
by Maasoon
I'm using a compreser and I have tryed a hand pump. If I think I know how these work, shouldnt the area above the diaphragm be the same pressure as the air tank? If so I don't think its happening in this valve is the diaphragm is completely air tight. Even when I block the barrel side and open the blow gun no air comes out. Could it be that with no air going in above the diaphragm that it is a lower pressure there already and the diapgram moves slightly up allowing small air flow??
Posted: Mon Jul 22, 2013 4:41 pm
by dewey-1
What brand and model?
Is there a hole in the center of the diaphragm with a screen in it?
Posted: Mon Jul 22, 2013 4:52 pm
by Maasoon
No should I drill one? There used to be a hole for a guide rod right in the center but I epoxed it :/ it was maybe 1-2mm big
Posted: Mon Jul 22, 2013 7:00 pm
by dewey-1
Yes, drill out that epoxy with about a 2.0mm drill,
You need an equalization hole.
Posted: Mon Jul 22, 2013 8:00 pm
by Maasoon
Its dead in the center in the plastic and does that mean the tank connects to the side where the inlet connects to the equalization hole yeah?
Posted: Thu Aug 01, 2013 5:34 am
by Maasoon
Hey everyone sorry to bump the thead but i kinda have it working. I drilled out the epoxy and it works well at 30-35 psi i have a resonbly small tank just the stock. I have pressued it to 120 psi however the valve does not fire correctly. It kinda just vibrates and makes a honk noise and the projectile will just fall out the end of the barrel.any ideas on how to fix? Is the equalization hole to big its 1mm atm