Here is my take on NoName's horizontal vortex(hortex block??) BBMG.
Though the concept is basically the same, the configuration is slighty different. I went with under/over as opposed to inline just because it seemed like a logical choice in reducing the overall size.
The gun is made from 1.5" pvc-pw, and the fittings are dwv. They are not cell core, however, so I have not and should not encounter any problems.
The block is glued into the bottom of the elbow.
The gun lives up to what is expected of a bbmg; so much so that I have "decomissioned" it because of the massive amount of ammo it goes through (don't worry, I didn't scrap it, I just stashed it away).
The only thing I can complain about it is once the spring is extended fully the ROF gets a bit choppy and sometimes needs a swift hit to un-jam.
Here's some pictures:
Fnord's sidestrafer.
-
Fnord
- First Sergeant 2
- Posts: 2239
- Joined: Tue Feb 13, 2007 9:20 pm
- Location: Pripyat
- Been thanked: 1 time
- Contact:
- Attachments
-
- Pretty basic setup.
Works though. - bbmg1.jpg (25.51 KiB) Viewed 3486 times
-
- bbmg2.jpg (38.77 KiB) Viewed 3486 times
-
- The block. (I added lines because one of the holes is hard to see)
-
- a few seconds of burst fire at close range.
Last edited by Fnord on Sat Aug 04, 2007 8:49 pm, edited 4 times in total.
-
homedepotpro
- Specialist 4
- Posts: 443
- Joined: Sun Nov 26, 2006 1:00 am
does this shoot .177 cal bbs. also is it a bondo block
nice, but what is the hole in the center of the block?
searching for a modern day savior from another place,inclined toward charity,everyone's begging for an answer,without regard to validity,the searching never ends,it goes on and on for eternity
-Bad religion
-Bad religion
-
Fnord
- First Sergeant 2
- Posts: 2239
- Joined: Tue Feb 13, 2007 9:20 pm
- Location: Pripyat
- Been thanked: 1 time
- Contact:
Yes, the bbs are .177 cal, but the block is pvc. there is a bit of epoxy on it because i screwed up when making it.
I used a .75" wood drill bit so the hole is where the predrilling tip went through the bottom. I sealed it up afterwards.
I used a .75" wood drill bit so the hole is where the predrilling tip went through the bottom. I sealed it up afterwards.
Last edited by Fnord on Sat Aug 04, 2007 8:28 pm, edited 1 time in total.
-
potatoflinger
- Sergeant 2
- Posts: 1136
- Joined: Thu Nov 02, 2006 3:26 pm
- Location: Maryland
That looks like it works pretty good, very nice!
-
singularity
- Corporal 5
- Posts: 982
- Joined: Mon Jun 26, 2006 10:53 pm
- Location: someplace
- Contact:
its a side strafer like the one noname made, the vortex block is tilted on its side, and the hole in the block is the vortex holenice, but what is the hole in the center of the block?
be sure to check out my <a href="http://www.spudfiles.com/forums/ak-styl ... 9.html">AK Styled Vortex Gun</a> and my <a href="http://www.spudfiles.com/forums/at-4-t9627.html">AT-4 Rocket</a>
upcoming projects... finalized clip fed BBMG and ball point pen sniper
upcoming projects... finalized clip fed BBMG and ball point pen sniper
-
jackssmirkingrevenge
- Five Star General
- Posts: 26203
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 569 times
- Been thanked: 344 times
looking very nice I have to say, though in performance terms not really any different from other BBMG configurations I presume?
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
Fnord
- First Sergeant 2
- Posts: 2239
- Joined: Tue Feb 13, 2007 9:20 pm
- Location: Pripyat
- Been thanked: 1 time
- Contact:
Well, it *appears* to shoot faster than the half-hole vortex gun I made, and it also seems a bit more reliable in terms of jamming.
I cant really get solid rps numbers out of it because I don't have the technology.
However, I do have an idea that could potentially change bbmgs forever. Right now I'm keeping it under wraps until I get a chance to build a functioning gun and compare the results. (It might show up in the next contest)
I cant really get solid rps numbers out of it because I don't have the technology.
However, I do have an idea that could potentially change bbmgs forever. Right now I'm keeping it under wraps until I get a chance to build a functioning gun and compare the results. (It might show up in the next contest)
