***Update*** 7/25/08 BAPCR

blind909 · Mon Jul 21, 2008 4:41 pm

The paintjob is awsome, did you just tear some strips of tape, or did you do that freehand?

MaxuS the 2nd · Mon Jul 21, 2008 4:53 pm

blind909 wrote:I realise that, so its more like a triggered Burst Disk Gun.

It's not really a triggered Burst Disc Gun either because you're just filling it till the disc bursts. A triggered burst disc launcher would be one that is pre-filled and then the disc is ruptured by outside means. Such as sgort's Burst Disc Gun, he has a pneumatic actuator in the chamber with a broadhead arrow on the end that pierced the disc on command.

blind909 · Mon Jul 21, 2008 5:41 pm

Then what is it, because Davids preloaded cartriges were just like this, just he used an air compressor, or Co2. Its just that mine has a handgrip, barrel extension, scope, and an onboard air setup.

MaxuS the 2nd · Mon Jul 21, 2008 5:44 pm

Well I don't really know, because all that's really happening is you're transferring air from one chamber into another one and the valve on the second chamber has a much higher flow coefficient than the first chamber.

So I suppose that it would be just 'Burst Disc Cartridge Gun'.
They're not really pre-loaded to be honest since pre-loading means to charge them before they are put into the gun.

blind909 · Mon Jul 21, 2008 6:08 pm

Yes, But His "preloaded cartrige" is not charged before he enters them into a gun, but after he does it.

Ragnarok · Mon Jul 21, 2008 6:19 pm

His description is a bit stretched. Strictly a preloaded cartridge needs to contain propellant, projectile, and some trigger mechanism, all before being loaded into the breach.

blind909 · Mon Jul 21, 2008 9:03 pm

Can Someone Delete This Post?

blind909 · Mon Jul 21, 2008 10:42 pm

Can Someone Delete This Post?

blind909 · Tue Jul 22, 2008 10:36 am

Updated Pics.

blind909 · Tue Jul 22, 2008 4:02 pm

Either today or tommorrow I will get a 1 1/4 inch to 2 inch bell reducer to put on the end of the gun as a muzzle brake.

SpudFarm · Tue Jul 22, 2008 4:03 pm

edit button

blind909 · Tue Jul 22, 2008 5:06 pm

I know, but is there any way I can delete the posts I made before the ones with the pictures, all the earased ones?

THUNDERLORD · Tue Jul 22, 2008 5:16 pm

That's one way to get a long thread going!

Looks cool!
Although I can't see the scope being very useful because the barrel is so short, the range is probably limited. But scopes are fun anyway.

Also, Where do you fill it from? And what kind of fitting is the barrel attached to? Looks like an end cap drilled out(?) 8)

blind909 · Tue Jul 22, 2008 5:25 pm

The barrel you see does nothing. The "barrel" you see is inside of a coupler. what I do is put some wadding inside the encap, then fill the endcap up with bbs, place a burst disk over the ammo, and close the bolt. To fill, I remove the stock via quick connect, and fill up the stock through a quick connect, and connect the chamber back onto the gun, via quick connect. And sinse the chamber is aluminum, I have no worries of Resting my cheek on it and it exploding. Basically what it is is a shotgun, that can shoot 200+ feet, so the scope is very good. I am going to home depot in about an hour or 2, so I am going to get a bell reducer, and drill holes in the end of it.

blind909 · Tue Jul 22, 2008 8:28 pm

ANOTHER UPGRADE: I added a 1 1/4 inch-2 inch ABS-DWV bell reducer on the end. I will either drill some holes in the end or get a triangular file and make it serated(?)

Update 7/25/08 BAPCR

Do You Like My Verminator, Or This Better?

Donating Members