pneumatic marker project
- inonickname
- First Sergeant 4
- Posts: 2606
- Joined: Sun Dec 07, 2008 3:27 am
You realize that there's another thread for this...it was finished and exploded ages ago. Have a look for it in the mini showcase. Check dates before posting
PimpAssasinG wrote:no im strong but you are a fat gay mother sucker that gets raped by black man for fun
- super spuder
- Corporal
- Posts: 558
- Joined: Fri Apr 06, 2007 9:05 pm
- Location: Ontario Canada
aww shit! my bad
trying to decide on a new project, probably something small.
- VH_man
- Staff Sergeant 4
- Posts: 1827
- Joined: Sat Dec 09, 2006 6:00 pm
- Location: New Hampshire
- Been thanked: 1 time
By the way JSR, have you ever looked at my .177 stick gun? I cant be arsed to find it at the moment, as im doing work, but It actually works very well as what you are describing.
If it wasnt a foot long, it would fit perfectly in a marker. The outside chamber is 1/2 copper and the inside is .18in ID aluminum tubing i ordered from Mcmaster.
As for the integral supressor, I think your going to have serious trouble in making that work reliably with the ammo going through the holed-out tubing. Unless your a machinist, And know how to make the holes perfect. Not saying dont try it, But the hole idea might not work as you think. If it were me, I would simply cut the barrel short at that point, and make the outlet part simply a .2in hole or something. That way theres no contact with the BB when it leaves the barrel.
I commend you for making theese cool things. I wish i wasnt in school so i could do theese things......
All in all, Good luck. And for all people wondering how loud a mini .177 gun can be, Its loud. My .177 stick gun makes my ears ring at 500......
If it wasnt a foot long, it would fit perfectly in a marker. The outside chamber is 1/2 copper and the inside is .18in ID aluminum tubing i ordered from Mcmaster.
As for the integral supressor, I think your going to have serious trouble in making that work reliably with the ammo going through the holed-out tubing. Unless your a machinist, And know how to make the holes perfect. Not saying dont try it, But the hole idea might not work as you think. If it were me, I would simply cut the barrel short at that point, and make the outlet part simply a .2in hole or something. That way theres no contact with the BB when it leaves the barrel.
I commend you for making theese cool things. I wish i wasnt in school so i could do theese things......
All in all, Good luck. And for all people wondering how loud a mini .177 gun can be, Its loud. My .177 stick gun makes my ears ring at 500......
- jackssmirkingrevenge
- Five Star General
- Posts: 26203
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 569 times
- Been thanked: 343 times
Just an update to clarify things, the marker gun was completed, tested and destroyed.
~ EPIC FAIL ~
I find no problems with this, I just make sure that I use a steel mandrel in the barrel while drilling to make sure I don't deform it, and that the holes are properly filed so as not to obstruct the barrel.
~ EPIC FAIL ~
This one? I had missed it, nice workBy the way JSR, have you ever looked at my .177 stick gun? I cant be arsed to find it at the moment, as im doing work, but It actually works very well as what you are describing.
As for the integral supressor, I think your going to have serious trouble in making that work reliably with the ammo going through the holed-out tubing. Unless your a machinist, And know how to make the holes perfect. Not saying dont try it, But the hole idea might not work as you think. If it were me, I would simply cut the barrel short at that point, and make the outlet part simply a .2in hole or something. That way theres no contact with the BB when it leaves the barrel.
I find no problems with this, I just make sure that I use a steel mandrel in the barrel while drilling to make sure I don't deform it, and that the holes are properly filed so as not to obstruct the barrel.
- jackssmirkingrevenge
- Five Star General
- Posts: 26203
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 569 times
- Been thanked: 343 times
I've decided to give this concept another go, with some modifications:
- metal chamber to avoid the epic fail that afflicted my first version, and to allow it to be used at 800 psi
- true 0.22" barrel as opposed to a 6mm calibre
- all rubber piston stamped out of a 5mm rubber sheet as in my pengun v2
Here's the parts before it all gets epoxied up. One thing to note is that since it will not be servicable, I've added a plastic collar to the barrel to widen the piston seat and reduce stress on the piston.
- metal chamber to avoid the epic fail that afflicted my first version, and to allow it to be used at 800 psi
- true 0.22" barrel as opposed to a 6mm calibre
- all rubber piston stamped out of a 5mm rubber sheet as in my pengun v2
Here's the parts before it all gets epoxied up. One thing to note is that since it will not be servicable, I've added a plastic collar to the barrel to widen the piston seat and reduce stress on the piston.
hectmarr wrote:You have to make many weapons, because this field is long and short life
- jackssmirkingrevenge
- Five Star General
- Posts: 26203
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 569 times
- Been thanked: 343 times
It should only give around 3 ft/lbs with a 0.22 pellet at 800 psi, but still much more powerful than the pen gun.looks good can't wait to see some results
A couple of millimetrestheBOOM wrote:Looks nice how much will the piston travel?
Simply take a section of chamber tubing, clamp it in a drill and sharpen it with a file. You can then either take the tubing out and hammer out a section of rubber (on a soft surface like wood or cardboard) or leave it in the drill and "punch" it out carefully. If you leave the latter method, be careful...how exactly did you "stamp" it out?
hectmarr wrote:You have to make many weapons, because this field is long and short life
- jackssmirkingrevenge
- Five Star General
- Posts: 26203
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 569 times
- Been thanked: 343 times
Yes, silly JSR was feeding the rubber into the drill as it was clamped in a vice, not the recommended way of doing thingstheBOOM wrote:Dang that had to hurt.. was that your finger, at first I thought it was a finger with no fingernail
No idea what it is exactly, just some scraps I found at work. Looks like neoprene.Is that rubber neoprene rubber or something else?
hectmarr wrote:You have to make many weapons, because this field is long and short life
- POLAND_SPUD
- Captain
- Posts: 5402
- Joined: Sat Oct 13, 2007 4:43 pm
- Been thanked: 1 time
I've had quite a lot of similar situations occuring...not the recommended way of doing things
normally my reaction was like:
or[RANDOM EXPLETIVES]... uhmm.. yeah that was dumb
[RANDOM EXPLETIVES]... uhmm.. so that's why I should never do it in this way !!
ohh btw JSR you've got a smiley on your finger... lol how cute
given the number of smileys that you shot to death I wonder if it's just a coincidence
in Soviet Russia smileys hurt you
Children are the future
unless we stop them now
unless we stop them now
- jackssmirkingrevenge
- Five Star General
- Posts: 26203
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 569 times
- Been thanked: 343 times
You asked for itPOLAND_SPUD wrote:ohh btw JSR you've got a smiley on your finger... lol how cute
given the number of smileys that you shot to death I wonder if it's just a coincidence
- Attachments
-
- Image179.jpg (10.46 KiB) Viewed 3752 times
hectmarr wrote:You have to make many weapons, because this field is long and short life
- POLAND_SPUD
- Captain
- Posts: 5402
- Joined: Sat Oct 13, 2007 4:43 pm
- Been thanked: 1 time
I was expecting it...
Have you been considering building a pneumatic walking stick ??
not to dis your construction methods but surely you could use a couple of threaded fittings.. one threaded pipe plus two home-made compression fittings and you've got a fully serviceable gunit will not be serviceable
Have you been considering building a pneumatic walking stick ??
Children are the future
unless we stop them now
unless we stop them now
- jackssmirkingrevenge
- Five Star General
- Posts: 26203
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 569 times
- Been thanked: 343 times
Of course this would be ideal, it's not that I use epoxy because I enjoy locking my projects up in such a manner that the only way to take them apart is to destroy them. It's just that I don't have sufficient metalworking facilities at hand and while I would like to eventually invest in them, my plate occupied by other things at the moment.POLAND_SPUD wrote:not to dis your construction methods but surely you could use a couple of threaded fittings.. one threaded pipe plus two home-made compression fittings and you've got a fully serviceable gun
What I really want to do is make one in a bicycle pump, Munich styleHave you been considering building a pneumatic walking stick?
hectmarr wrote:You have to make many weapons, because this field is long and short life
- POLAND_SPUD
- Captain
- Posts: 5402
- Joined: Sat Oct 13, 2007 4:43 pm
- Been thanked: 1 time
I meant standard (or slightly modified) fittings... sure they are not ideal
if standard fittings are not enough you can always mod them: add an o ring or rubber washer here and there and so on... actually you could even combine them with epoxy
ohh and if you are looking for unusual parts (like metric to imperial adapters or ready made compression fittings) there are lots of them in old equipment, weed sprayers, valves, taps etc.
surely you can find a lot of parts in all those parts that are throw away at your work
if standard fittings are not enough you can always mod them: add an o ring or rubber washer here and there and so on... actually you could even combine them with epoxy
ohh and if you are looking for unusual parts (like metric to imperial adapters or ready made compression fittings) there are lots of them in old equipment, weed sprayers, valves, taps etc.
surely you can find a lot of parts in all those parts that are throw away at your work
Children are the future
unless we stop them now
unless we stop them now