Double Shot (High Pressure Mini)
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
Thanks Solar, what size valve does the piston above actuate?
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
-
Solar
- Corporal
- Posts: 545
- Joined: Tue May 17, 2005 11:53 pm
- Has thanked: 1 time
- Been thanked: 17 times
It has a 1" port. The picture shows both the piston actuator and the valve. The air intake is at the threaded end you see, and the output it through the turned down area with the omni directional holes. A manifold slips over the o-rings to direct the air through the barrel.
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
What kind of sights do you think i should use on my gun? Any ideas welcome.
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
Carefully and neatly JB weld a nut horizontally on the front after measuring out where the center is. Then, put an eyescrew in it. For the rear, put another nut, but smaller, and then a screw. This way, you can adjust the sights. However, you couldn't adjust them laterally.... Maybe use neomidium magnets with the setup glued on to them? Nice neomidium magnets are super strong, and not likely to get pulled off with anything short of a pair of plyers. Then they would be stuck to you pliers.... 
However, you could probably still slide them.
However, you could probably still slide them.
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
Edit: The ammo i use is like the blue one in the picNovacastrian wrote:At the local scrapeyard, sadly it was closed down about 1 month agoHaiThar wrote:Very Nice build. I love the gold plate. Where did you get the chamber from?
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
My tip would be to go to a lighting store, i think the pole i used was an ex light fitting pole thingy.
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
Than wouldn't that mean it won't hold much pressure.....?
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
Any aluminium that dia with a wall thickness of 3mm should be pretty good at holding pressure.
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
-
Novacastrian
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
I am going to test it past 300psi. Just think about how much pressure a soda bottle can hold (150psi) The weakest part of my chamber would be where the gauge goes in= don't point gauge towards face whilst pumping. I might test it with water.
America, the greatest gangster of all time. With 200 million odd foot soldiers at it's whim and call.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
When you fill your car with refined oil remember that it has been paid for with blood and guts, some from your own countrymen, most not.
-
jackssmirkingrevenge
- Five Star General
- Posts: 26203
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 569 times
- Been thanked: 344 times
How about epoxying a dovetail plate to the top of the chamber and fitting one of these?Novacastrian wrote:What kind of sights do you think i should use on my gun?
Cheap and well suited to spudgun applications
Even simpler would be to make up some adjustable iron sights - even with my limited facilities I managed to make some for this launcher, so with what you have at your disposal it should be a piece of cake.
hectmarr wrote:You have to make many weapons, because this field is long and short life
Oh, I didn't see the part about it being 3mm thick.