XxtriviumxX said my last bbmg looked like a MP 40. After seeing the picture I decided to make one.
I tried to make it as close to a real one. It has a tight bore barrel 12 in. long. the grip and mag and about everything else is pvc. The tapered outer barrel is an old golf club shaft. I used ferrel fitting to run from the blow gun to the block which is plexiglass. I put a smaller plexiglass window in this one.
MP 40 BBMG
-
Stephen Holliday
- Private 3
- Posts: 41
- Joined: Tue Apr 01, 2008 10:25 am
- Attachments
-
- looking from side
- MVC-044S.JPG (37.59 KiB) Viewed 5124 times
-
- front view
- MVC-043S.JPG (37.33 KiB) Viewed 5124 times
-
- stock out
- MVC-042S.JPG (36.94 KiB) Viewed 5124 times
-
- stock up
- MVC-041S.JPG (36.31 KiB) Viewed 5124 times
Last edited by Stephen Holliday on Tue May 13, 2008 4:05 pm, edited 1 time in total.
-
magnum9987
- Specialist 2
- Posts: 274
- Joined: Wed May 07, 2008 5:02 pm
How much do these things cost to build?
POst a vid of this thing in action!
POst a vid of this thing in action!
http://www.spudfiles.com/forums/viewtop ... Revolution in the absolute is not initiated by swords, guns, and bullets, but by words-
The New RobesPierre
The New RobesPierre
-
Davidvaini
- Sergeant 4
- Posts: 1315
- Joined: Tue May 29, 2007 8:58 pm
looks good... im glad to see you used a tightbore..
One suggestion would be to clean up around the trigger area... but other than that it looks great!
One suggestion would be to clean up around the trigger area... but other than that it looks great!
wow dude, that is SICK!!! very nice job. Lovin' the collapsable stock 8)
Again, nice work
Again, nice work
Forum Rules - follow them or else!
“Happiness is the meaning and the purpose of life, the whole aim and end of human existence”
“Happiness is the meaning and the purpose of life, the whole aim and end of human existence”
-
Stephen Holliday
- Private 3
- Posts: 41
- Joined: Tue Apr 01, 2008 10:25 am
It doesn't cost much to build one. The barrel cost more then anything else. It takes a lot of time because everything is custom fitted.How do you post a video? I've looked for information but haven't found anything about posting videos. I can take the grip off easily and may put a push button blow gun in place of the one with the handle. Fix a trigger on it to push against the button.
Last edited by Stephen Holliday on Wed May 14, 2008 6:58 am, edited 1 time in total.
-
bigbob12345
- Staff Sergeant
- Posts: 1516
- Joined: Sat Dec 01, 2007 9:13 am
- Location: Mercer Island,Washington
You post a video by uploading it on youtube/photobucket and then link it to here.
But really nice work
And how is accuraccy?
But really nice work
And how is accuraccy?
If you don't mind me asking....What did you use for the magazine clip/handle? It looks very realistic. Toy gun I presume?...
Forum Rules - follow them or else!
“Happiness is the meaning and the purpose of life, the whole aim and end of human existence”
“Happiness is the meaning and the purpose of life, the whole aim and end of human existence”
-
Stephen Holliday
- Private 3
- Posts: 41
- Joined: Tue Apr 01, 2008 10:25 am
I'll have to try a video. It is accurate, doesn't spread the bbs like some I 've made. It would keep shooting through the same hole if you didn't move it. I've only tried it at 25 feet for test fire.
-
Stephen Holliday
- Private 3
- Posts: 41
- Joined: Tue Apr 01, 2008 10:25 am
I heated a 1 in. piece of pvc and flattened it and flattened the T where it went in. I cut a piece of pvc for the bottom of the clip. The grip was 2 in. heated and formed.
I have a radiant heater in the garage that i use to heat up the pvc. I can hold it their till it get soft without burning it and then form it the way I want.
I have a radiant heater in the garage that i use to heat up the pvc. I can hold it their till it get soft without burning it and then form it the way I want.
Last edited by Stephen Holliday on Tue May 13, 2008 6:22 pm, edited 2 times in total.
very nice. and next time, just use the "edit" option instead of double-posting.
but how did you go upon heating the pvc? oven or boiling water? I'm pretty sure you didn't use a torch because I don't see any scorch marks...
anyway, very nice job! hope to see more projects from you 
but how did you go upon heating the pvc? oven or boiling water? I'm pretty sure you didn't use a torch because I don't see any scorch marks...
anyway, very nice job! hope to see more projects from you
Forum Rules - follow them or else!
“Happiness is the meaning and the purpose of life, the whole aim and end of human existence”
“Happiness is the meaning and the purpose of life, the whole aim and end of human existence”
Hey not bad... Actually, quite good. I like it! When I make a vortex, (as opposed to my clouds) I MUST make it look like something. Wait a second.... HEH, I got an old medium sized LPEG. Sorta M4 ish. Heck, it's worth a try, that gun sucks.
EDIT: Oh, and btw the mp40 wasn't the grease gun. The mp40 was a german gun. The m3 was the grease gun, and american gun.
When I make a vortex, (as opposed to my clouds) I MUST make it look like something. Wait a second.... HEH, I got an old medium sized LPEG. Sorta M4 ish. Heck, it's worth a try, that gun sucks.EDIT: Oh, and btw the mp40 wasn't the grease gun. The mp40 was a german gun. The m3 was the grease gun, and american gun.
-
Pyro Ninja
- Specialist 3
- Posts: 351
- Joined: Mon Oct 09, 2006 7:11 am
- Location: Australia
Love it, looks the part
Doesn't look like there is much to clean up.Davidvaini wrote:One suggestion would be to clean up around the trigger area...