I have not done the system of electrodes / / but I opted instead for a plug HM.
You can also see a seal that helps me when I want to unscrew the spark plug to clean it.
I tested this config up to 40bar and no worries, the spark is good.
Hybrid ThorJack
I redid my electrodes hoping to be able to do with my flash Mix40:
I have not done the system of electrodes / / but I opted instead for a plug HM.
You can also see a seal that helps me when I want to unscrew the spark plug to clean it.
I tested this config up to 40bar and no worries, the spark is good.
I have not done the system of electrodes / / but I opted instead for a plug HM.
You can also see a seal that helps me when I want to unscrew the spark plug to clean it.
I tested this config up to 40bar and no worries, the spark is good.
-
killerbanjo
- Specialist 2
- Posts: 245
- Joined: Fri Jun 18, 2010 6:56 pm
Looks nice and clean mate, really looking forward to the finished product
-
killerbanjo
- Specialist 2
- Posts: 245
- Joined: Fri Jun 18, 2010 6:56 pm
Sweet 
looking forward to it
looking forward to it-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
can you give me the exact diameter of the copper pipe? It's easier to make the sabots for a smoothbore barrel 
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
Yes, and also there's a lot less friction drag - that's why modern tanks have smoothbore barrelsPetitlu wrote:But in a smooth barrel not rotating the bullet ...
Note with a sphere or an arrow that's not important ...
What's the thickness of the copper?will support the smooth barrel Mix40?
What does this mean exactly - did you put it inside an iron tube?covered with iron
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
wall thickness of the iron tube?
is it an exact fit?
is it an exact fit?
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
Shouldn't be a problem.
I've done some machining in the meantime, i apologise that the workmanship is quite shoddy and rough, I don't have much free time at the moment - but it should all fit well and give you some good results
There's 5 8mm bearing sabots for your rifled barrel, 4 collars and pusher plates for your smoothbore barrel and 3.4mm diameter nails that should slip on without modification, and two tail sections that would require you to cut the head off the nails.
I've done some machining in the meantime, i apologise that the workmanship is quite shoddy and rough, I don't have much free time at the moment - but it should all fit well and give you some good results
There's 5 8mm bearing sabots for your rifled barrel, 4 collars and pusher plates for your smoothbore barrel and 3.4mm diameter nails that should slip on without modification, and two tail sections that would require you to cut the head off the nails.
- Attachments
-
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
No worries, will post them tomorrowPetitlu wrote:Thank you!
I can not wait to test all these shoes!
looking forward to your results.I'm hoping the centrifugal force on the 8mm sabots in the rifled barrel will help the sabot spread and separate.
Don't bother too much, they are going to be fired after allI will remove the burrs, no problem!
Thinking about it, it's best if you cut off the heads of all the nails you use, in order to avoid the weight at the back making it tail-heavy. A bit of 5 minute epoxy to keep the nails in place should be enough.
hectmarr wrote:You have to make many weapons, because this field is long and short life