Easy as pie CO2/HPA setup for BBMGs!
- iPaintball
- Corporal 2
- Posts: 695
- Joined: Sun Mar 04, 2007 8:37 pm
I was searching through my old paintball gun parts and I found an ASA thread adapter (the kind used on drop forwards) with an on/off button. Then it hit me! If you don't have the budget for a Palmer Reg, buy an on/off ASA adapter! The standard output for these is 1/8 NPT so it will screw directly on to a 1/8" close nipple. I've seen these adapters for as little as $10, so there perfect if you're low on cash. As for the extreme pressure created by CO2/HPA bottles, don't worry about it. You can easily adjust the flow by turing the bottle like a screw valve! It works perfectly on my BBMG, but the only disadvantage is you can't use a blowgun trigger, so you just use the on/off switch as a trigger. To me, this is definitely worth saving $69, and for most of you, I'm sure it is too! Let me know what you think!
- iPaintball
- Corporal 2
- Posts: 695
- Joined: Sun Mar 04, 2007 8:37 pm
Well, it depends. As far as I know, you cant use a blowgun because of the high pressure, but if you had an inline pressure gauge and a pop-off valve (set to, say, 120 psi) before the blowgun, you might be able to adjust the pressure so you can use it safely. Same thing with the ball valve.
yea one thats rated to 1000 psi for co2hi wrote:you said that you cant use a blowgun, could you use a ball valve, maybe 1/4 inch?
800 for HP HPA
and 500 for LP HPA
Im look to get an adjustable regulator for my HPA tank... that would be perfect for all this
- iPaintball
- Corporal 2
- Posts: 695
- Joined: Sun Mar 04, 2007 8:37 pm
The regulator on my HPA tank is a LP 500 psi preset, so I can't adjust it. I designed this setup for use without expesive regulators.
Oh and CO2 bottles are 600-800 psi...
Oh and CO2 bottles are 600-800 psi...
- iPaintball
- Corporal 2
- Posts: 695
- Joined: Sun Mar 04, 2007 8:37 pm
Oh...sorry, someone at Dick's Sporting Goods told me that, whatever...
- singularity
- Corporal 5
- Posts: 982
- Joined: Mon Jun 26, 2006 10:53 pm
- Location: someplace
- Contact:
i bought a regulator for a co2 tank, i don't know what type it is but it screwed onto the tank and 90 degrees from that was a 1/8 npt port ant you turned to top to adjust the pressure. anyway i never got a chance to test it because i dropped it and the pin popped out of it. wont it be kinda low flow though?
be sure to check out my <a href="http://www.spudfiles.com/forums/ak-styl ... 9.html">AK Styled Vortex Gun</a> and my <a href="http://www.spudfiles.com/forums/at-4-t9627.html">AT-4 Rocket</a>
upcoming projects... finalized clip fed BBMG and ball point pen sniper
upcoming projects... finalized clip fed BBMG and ball point pen sniper
Not a good regulator.singularity wrote:i bought a regulator for a co2 tank, i don't know what type it is but it screwed onto the tank and 90 degrees from that was a 1/8 npt port ant you turned to top to adjust the pressure. anyway i never got a chance to test it because i dropped it and the pin popped out of it. wont it be kinda low flow though?
And yea co2 can go from like 600 when cold to 1200 when hot